
sds_black_top_coat.pdf | |
File Size: | 139 kb |
File Type: |
CrystaLac Colored Top Coats are made in our Waterbased Extreme Protection Polyurethane by adding highly concentrated colorants, giving you a high quality, super durable coating. No need to top coat as it already is a Polyurethane Top Coat with the addition of color. UV Stabilized and Non- Yellowing.
Available Colors: Each Color can be mixed to create new colors
Black Gloss
Black Satin
White Gloss
White Satin
Red Gloss
Blue Gloss
Yellow Gloss
Green Gloss (Seasonal)
With proper prep, (cleaned and scuff sanded) Extreme Protection will bond to Wood, Metal, Plastic ,Fiberglass, Ceramics, Tile and Glass.
Extreme Protection Polyurethane ( Colored Top Coats Base) is an Interior, NON- YELLOWING, Environmentally Safe Top Coat that is Super Hard, Super Clear and Super Easy to Use. It is Scratch, Chemical, and Water Resistant. It Self- Levels, has Low Odor, Low V.O.C. and cleans up with water.
Use anywhere an extra level of protection is needed. Added UV stabilizers will keep dyes and stains brilliant and will help protect colors from fading.
CrystaLac Polyurethane can be applied by either brushing or spraying (gravity feed or HVLP sprayer) Use a good quality brush.
It is not necessary to sand between each Top Coat. All CrystaLac Top Coats will bond to the prior coat. CrystaLac Top Coats can be used over thoroughly dried oil or water-based stains, shellac, lacquer, Polyurethane or Acrylic. If re-coating over an old finish, scuff sand first and remove any surface contaminants such as dirt, waxes or polishes.
Usually 3 to 5 coats are sufficient to produce a beautiful, protective finish. Use more if desired.
Coverage is approximately 400 to 500 sq. ft. per gallon.
Dry time is usually 30 min to 1 hour. Allow 2 to 4 hours before re-coating.
Do Not use stearated sandpaper or tack cloths. Do Not freeze. Do Not apply below 60 degrees.
Do Not thin or clean with lacquer solvents or mineral spirits. Use soap and water for clean-up.
Warranty: Test to your satisfaction on scrap material before using. The manufacturer, The CrystaLac Company, will only replace defective product. Under no circumstances will the manufacturer or distributors be responsible for the cost of application labor, refinishing expenses, or any costs more than the purchase price of the container.
Caution: Keep out of reach of children! Do not ingest. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 Lbs. per gallon.
Disposal: Consult your local sanitation department. Do not dump on the ground.
Available Colors: Each Color can be mixed to create new colors
Black Gloss
Black Satin
White Gloss
White Satin
Red Gloss
Blue Gloss
Yellow Gloss
Green Gloss (Seasonal)
With proper prep, (cleaned and scuff sanded) Extreme Protection will bond to Wood, Metal, Plastic ,Fiberglass, Ceramics, Tile and Glass.
Extreme Protection Polyurethane ( Colored Top Coats Base) is an Interior, NON- YELLOWING, Environmentally Safe Top Coat that is Super Hard, Super Clear and Super Easy to Use. It is Scratch, Chemical, and Water Resistant. It Self- Levels, has Low Odor, Low V.O.C. and cleans up with water.
Use anywhere an extra level of protection is needed. Added UV stabilizers will keep dyes and stains brilliant and will help protect colors from fading.
CrystaLac Polyurethane can be applied by either brushing or spraying (gravity feed or HVLP sprayer) Use a good quality brush.
It is not necessary to sand between each Top Coat. All CrystaLac Top Coats will bond to the prior coat. CrystaLac Top Coats can be used over thoroughly dried oil or water-based stains, shellac, lacquer, Polyurethane or Acrylic. If re-coating over an old finish, scuff sand first and remove any surface contaminants such as dirt, waxes or polishes.
Usually 3 to 5 coats are sufficient to produce a beautiful, protective finish. Use more if desired.
Coverage is approximately 400 to 500 sq. ft. per gallon.
Dry time is usually 30 min to 1 hour. Allow 2 to 4 hours before re-coating.
Do Not use stearated sandpaper or tack cloths. Do Not freeze. Do Not apply below 60 degrees.
Do Not thin or clean with lacquer solvents or mineral spirits. Use soap and water for clean-up.
Warranty: Test to your satisfaction on scrap material before using. The manufacturer, The CrystaLac Company, will only replace defective product. Under no circumstances will the manufacturer or distributors be responsible for the cost of application labor, refinishing expenses, or any costs more than the purchase price of the container.
Caution: Keep out of reach of children! Do not ingest. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 Lbs. per gallon.
Disposal: Consult your local sanitation department. Do not dump on the ground.