PolyOxide Wood Floor Finish
CrystaLac PolyOxide Wood Floor Finish is a Gymnasium Tough, Heavy Duty, Non-Yellowing, Scuff Resistant, Water Based Polyurethane that is U.V. Stabilized and Fortified with Aluminum Oxide for Exceptional Durability.
CrystaLac PolyOxide Wood Floor Finish is an amazing, easy to use, water based polyurethane finish. It can be brushed, sprayed or mopped on with a lamb's wool applicator. The finish dries to the touch within an hour and additional coats can be applied every two hours. A flooring project can be completed with four to five coats applied in only one days' time!
Another advantage of using PolyOxide Wood Floor Finish is that there is virtually no smell. This is a great benefit when doing home projects. Traditional polyurethane wood floor finish can leave harmful, lingering odors for weeks.
CrystaLac PolyOxide Wood Floor Finish is an amazing, easy to use, water based polyurethane finish. It can be brushed, sprayed or mopped on with a lamb's wool applicator. The finish dries to the touch within an hour and additional coats can be applied every two hours. A flooring project can be completed with four to five coats applied in only one days' time!
Another advantage of using PolyOxide Wood Floor Finish is that there is virtually no smell. This is a great benefit when doing home projects. Traditional polyurethane wood floor finish can leave harmful, lingering odors for weeks.
PolyOxide Use and Instructions
www.crystalac.info
PolyOxide is made with rubber tough, self- curing, waterborne polyurethane resins. It is fortified with Aluminum Oxide and U.V. stabilizers for years of floor protection and beautification. It has no harsh odors.
PolyOxide can be applied over any clean, sanded surface, and is compatible with thoroughly dried oil or water based stain. PolyOxide dries to touch in 30 minutes and cures hard in 24 hours. Covers 400 sq. ft. per Gal.
PolyOxide can be applied using a lamb’s wool applicator, brush, or spray gun.
Stir contents gently but thoroughly. Do Not Shake. Apply 4 or more coats allowing 2 hours of drying time between coats. Lightly scuff sand after first coat to remove any raised grain or fibers. Additional sanding between coats is not necessary. Do Not Use stearated sandpaper or tack cloths. Rinse applicators with warm soapy water. Any leftover PolyOxide can be stored in a clean, air-tight container for future use.
First Aid: If swallowed, call a physician immediately. In case of eye contact, flush with water. Wash off skin with soap and water.
Disposal: Consult your local sanitation department. Do not dump on the ground.
Warranty: Test to your satisfaction on scrap material before using. The manufacturer, The CrystaLac Company, will only replace defective product. Under no circumstances will the manufacturer or distributors be responsible for the cost of application labor, refinishing expenses, or any costs in excess of the purchase price of the container.
Caution: Keep out of reach of children! Do not ingest. Avoid contact with skin and eyes. Do not breathe vapors. Use with adequate ventilation. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 Lbs. per gallon.
www.crystalac.info
PolyOxide is made with rubber tough, self- curing, waterborne polyurethane resins. It is fortified with Aluminum Oxide and U.V. stabilizers for years of floor protection and beautification. It has no harsh odors.
PolyOxide can be applied over any clean, sanded surface, and is compatible with thoroughly dried oil or water based stain. PolyOxide dries to touch in 30 minutes and cures hard in 24 hours. Covers 400 sq. ft. per Gal.
PolyOxide can be applied using a lamb’s wool applicator, brush, or spray gun.
Stir contents gently but thoroughly. Do Not Shake. Apply 4 or more coats allowing 2 hours of drying time between coats. Lightly scuff sand after first coat to remove any raised grain or fibers. Additional sanding between coats is not necessary. Do Not Use stearated sandpaper or tack cloths. Rinse applicators with warm soapy water. Any leftover PolyOxide can be stored in a clean, air-tight container for future use.
First Aid: If swallowed, call a physician immediately. In case of eye contact, flush with water. Wash off skin with soap and water.
Disposal: Consult your local sanitation department. Do not dump on the ground.
Warranty: Test to your satisfaction on scrap material before using. The manufacturer, The CrystaLac Company, will only replace defective product. Under no circumstances will the manufacturer or distributors be responsible for the cost of application labor, refinishing expenses, or any costs in excess of the purchase price of the container.
Caution: Keep out of reach of children! Do not ingest. Avoid contact with skin and eyes. Do not breathe vapors. Use with adequate ventilation. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 Lbs. per gallon.
Properties of PolyOxide :
- Fast Drying
- Water Clean-Up
- U.V. Stabilized
- Scuff Resistant
- Non-Yellowing
- Non-Flammable
- Non-Toxic
- Low V.O.C.
- No Lingering Paint Smell