Keep up to date through our Social Network
The CrystaLac Company
  • Home
    • Contact
    • About Us
    • FAQ
    • Reviews
    • Where to Buy >
      • The CrystaLac Store
    • Join Our Team
  • Project Categories
    • Tumbler Coatings
    • Furniture Flipping/Refinishing
    • Wood Finishing >
      • Guides 1: Prep
      • Guide 2 : Sanding Sealer
      • Guide 3: Wood Grain Filler
      • Guide 4: Topcoats/ Sealer
      • Guide on Staining
    • Luthier & Instruments
  • Product Catalog
    • Grande Finale Tumbler Coat
    • Brite Tone TopCoat
    • Extreme Protection Polyurethane Top Coat
    • Colored Top Coats
    • CrabCoat Marine/Exterior Finish
    • Paints/ Primers >
      • Universal White & Gray Primer
      • Flip'N Awesome 3 in 1
    • Gel Stain and Glaze
    • CraftNique Pigments & Micas
    • Inks
    • It's "Knot" Shellac Tannin Blocking Clear Sealer
    • Sanding Sealer/Wood Enhancer- Amber Toned
    • Clear Wood Grain Filler
  • Guide to Waterborne Finishes
  • Blog
Extreme Protection Polyurethane SDS.pdf
File Size: 135 kb
File Type: pdf
Download File

Extreme Protection technical data
File Size: 141 kb
File Type: pdf
Download File

Buy Here
Extreme Protection Waterbased Polyurethane is an Interior, NON- YELLOWING, Environmentally Safe Top Coat that is Super Hard, Super Clear and Super Easy to Use. It is Scratch, Chemical, and Water Resistant. It Self- Levels, has Low Odor, Low V.O.C.  and cleans up with water.

Available in 4 Sheens  Gloss, Semi-Gloss, Satin and Matte


 Use anywhere an extra level of protection is needed. Added UV stabilizers will help to keep dyes and stains brilliant and minimizes  colors from fading. Dries crystal clear even over white finishes. It is always important to use a good tannin blocking primer under white or light colored paints. Otherwise your waterbased topcoat will pull tannins through the paint to the surface. We recommend our Universal White Stain Blocking / Bonding Primer or our Clear "It's Knot Shellac". 


Excellent for use on:
Table Tops
Floors
Cabinetry
Furniture
Hobbies & Crafts
ETC...


CrystaLac Polyurethane can be applied by either brushing or spraying (gravity feed or HVLP sprayer). Use a good quality brush.
Prior to Top Coating, we recommend using CrystaLac Amber Toned Sanding Sealer to enrich the warm natural colors in the wood and minimize grain raising.
It is not necessary to sand between each Top Coat. All CrystaLac Top Coats will bond to the prior coat. CrystaLac Top Coats can be used over thoroughly dried oil or water-based stains, shellac, lacquer, Polyurethane or Acrylic.  If recoating over an old finish, scuff sand first and remove any surface contaminants such as dirt, waxes or polishes.
Usually 3 to 5 coats are sufficient to produce a beautiful, protective finish. Use more if desired.
Coverage is approximately 400 to 500 sq. ft. per gallon.
Dry time is usually 30 min to 1 hour. Allow 2 to 4 hours before recoating.
Do Not use stearated sandpaper or tack cloths. Do Not freeze. Do Not apply below 60 degrees.
Do Not thin or clean with lacquer solvents or mineral spirits. Use soap and water for clean-up.
Warranty: Test to your satisfaction on scrap material before using. The manufacturer, The CrystaLac Company, will only replace defective product. Under no circumstances will the manufacturer or distributors be responsible for the cost of application labor, refinishing expenses, or any costs more than the purchase price of the container.
Caution: Keep out of reach of children! Do not ingest. Avoid contact with skin and eyes. Do not breathe vapors. Use with adequate ventilation. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 Lbs. per gallon.
Disposal: Consult your local sanitation department. Do not dump on the ground.


Proudly powered by Weebly